Just how do you really feel in regards to How to Install a Bathtub?
Installing a bath tub isn't exactly rocket science, yet it does need solid plumbing, woodworking, and sometimes, tiling skills. Replacing an old bath tub with a new one is likewise a moderately difficult job. If the old tub is conveniently easily accessible, the project can move immediately; if you have to open a wall surface to remove the old tub as well as place the new bath tub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly need an assistant to move out the old tub and embeded in the new one. Make certain you have certified on your own for the work and also fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is better to think about employing one prior to you start. Possibilities are you may require a specialist plumber to make tube connections.
This short article will certainly aid you set up a new bathtub in your washroom if you have actually already acquired a new bathtub as well as do not need to transform the plan of your previous supply of water pipelines.
Your tools as well as material checklist need to comprise the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you need to do is separate the supply of water. After doing so, switch on the taps to drain any kind of water remaining in the system. The procedure of removing the existing taps can be rather problematic as a result of the restricted access that is commonly the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric all set for the continuing to be water that will come from the pipelines. Once the supply pipelines have been gotten rid of, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. Once the taps have actually been removed, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to moving on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end provides a connection to the current supply pipes.
If you require to fit a monobloc, after that you will call for lowering couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the installing opening in the bath/basin making certain that the washing machines remain in location in between the tap and also the sink. Secure the tap in place with the supplier offered backnut. When the tap is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with typical tap connectors. The previous kind needs to be connected to the faucet ends first, tightening just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Utilizing both wooden boards under its feet, put the bathtub in the called for setting. The wood boards are helpful in evenly spreading out the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small points.
The next goal is to ensure that the tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bath tub until the spirit level reads level.
To install faucets, fit all-time low of the outermost versatile tap port to the ideal supply pipeline by making a compression join; then do the exact same for the other tap.
Activate the water supply and examine all joints and also new pipework for leaks and tighten them if essential. Load the tub as well as additionally inspect the overflow outlet and the typical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the bathtub needs to wait up until the tub has been made use of at least once as this will certainly settle it right into its final position.
Preparing for the Installation
First of all, the sustaining frame supplied with the bathroom should be fitted (if required) according to the supplier's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to see to it that if the faucet includes a plastic washer, it is fitted between the bath and also the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the taps device to stop pressure on the bath tub.
Fit the flexible faucet connectors to the bottom of the two faucets making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath should currently be ready to be suited its last position.
Tiling Around the Bath tub
In the location where the bath satisfies the floor tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to split a rigid seal, creating the water to permeate the wall in between the bath as well as the tiling, resulting in complications with moisture and feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your components and fittings. They are marketed in tubes and also cartridges, and can securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water prior to securing, to permit the movement experienced when the tub remains in usage. The sealer can break relatively very early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I recently found that page about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when perusing the internet. Appreciated our write-up? Please share it. Help other people find it. Thanks for taking the time to read it.
Achieve peace of mind.